Close-up of turbofan engine fan blades

Technique Explorer

See how each technique finds a discontinuity. Choose your industry, a method and a technique, and the demo runs the examination on a part that industry examines: the probe, source or camera moves over the part, the display builds, and each discontinuity shows the way that technique reports it. Each demo also shows the setup, and a follow-up view where a technique misses a discontinuity or reports it weakly.

Run a Technique Demo

Techniques by Method

Ultrasonic Testing

Ultrasonic Testing (UT): Zero Degree

Laminations, inclusions and internal discontinuities in plate, forgings, bar and castings, and wall measurement where a back wall is available. Views in the demo: A-scan, B-scan, gate profile, amplitude C-scan and thickness C-scan, plus a follow-up view.

Discontinuities and features shown: lamination, inclusion stringer and inclusion cluster.

  • General Industry
  • Aerospace: Forgings, bar and plate for airframe and engine parts, and bonded or machined fittings, inspected to the customer specification.
  • Oil & Gas: Plate and pipe laminations before welding, nozzle reinforcement areas, and wall checks at corrosion monitoring locations.
  • Power & Nuclear: Forgings, bolting, castings and plate in pressure-retaining components.
  • Wind Energy: Main shaft, bolting and cast hub material before and after service.
  • Marine & Shipbuilding: Hull and deck plate laminations before fit-up, and forgings in propulsion components.

Open this demo

Ultrasonic Testing (UT): Shear Wave, Angle Beam

Butt and fillet welds in steel structures, pressure equipment and piping, with angles chosen to meet each fusion face. Views in the demo: A-scan, echo amplitude and indication plot, plus a follow-up view.

Discontinuities and features shown: toe crack, cluster porosity, side-wall lack of fusion, slag line, incomplete penetration and root crack.

  • General Industry
  • Oil & Gas: Pipe, vessel and structural welds in fabrication and in service, including nozzle and attachment welds.
  • Power & Nuclear: Pressure-boundary and structural welds, and in-service examination of known damage areas.
  • Wind Energy: Tower flange and shell welds, and transition piece welds.
  • Civil & Infrastructure: Complete joint penetration welds in moment connections, bridges and structural steel.
  • Marine & Shipbuilding: Hull, deck and structural welds in new construction and repair.

Open this demo

Phased Array Ultrasonic Testing (PAUT): Angle Beam

Encoded examination of welds with a recorded image, often in place of radiography where the code allows. Views in the demo: S-scan, A-scan, C-scan, side view and echo amplitude, plus a follow-up view.

Discontinuities and features shown: toe crack, cluster porosity, side-wall lack of fusion, slag line, incomplete penetration and root crack.

  • General Industry
  • Oil & Gas: Girth, seam and nozzle welds, with encoded data retained for review and repeat examination.
  • Power & Nuclear: Thick-wall pressure-boundary girth welds in low-alloy steel piping. Dissimilar metal and austenitic welds are examined with the dual linear array.
  • Wind Energy: Tower and foundation welds in fabrication.
  • Civil & Infrastructure: Bridge and building connection welds where access is from one side.
  • Marine & Shipbuilding: Hull and structural welds with recorded coverage.

Open this demo

Phased Array Ultrasonic Testing (PAUT): Zero Degree

Corrosion and lamination mapping of plate and shell, with recorded thickness and amplitude maps. Views in the demo: L-scan, B-scan, thickness map, back wall amplitude and A-scan, plus a follow-up view.

Discontinuities and features shown: general wall loss with pits, isolated pit, lamination, inclusion cluster and inclusion stringer.

  • General Industry
  • Aerospace: Composite skins and spars mapped for porosity, delamination and disbond.
  • Oil & Gas: Internal corrosion and hydrogen damage mapping in vessels, tanks and piping, with a baseline for the next survey.
  • Power & Nuclear: Wall loss and lamination mapping on plant vessels, tanks and piping.
  • Wind Energy: Blade spar caps, bondlines and the leading edge and trailing edge, mapped for porosity, delamination and disbond.
  • Marine & Shipbuilding: Tank and hull plate thickness and lamination mapping.

Open this demo

Time of Flight Diffraction (TOFD)

Detection and through-wall height sizing of planar discontinuities in welds. Views in the demo: A-scan and D-scan, plus a follow-up view.

Discontinuities and features shown: toe crack, cluster porosity, side-wall lack of fusion, slag line, incomplete penetration and root crack.

  • General Industry
  • Oil & Gas: Crack height measurement for fitness-for-service assessment by the owner’s engineer, and repeat scans to watch for growth.
  • Power & Nuclear: Weld examination of thick pressure components with sizing data retained.
  • Wind Energy: Thick monopile and transition piece welds.
  • Marine & Shipbuilding: Thick hull and offshore-grade welds, with through-wall height sizing.

Open this demo

Ultrasonic Testing (UT): Immersion, Composites

Automated, encoded examination of parts that fit an immersion tank or gantry. Views in the demo: A-scan, C-scan (echo amplitude), C-scan (back-wall amplitude), C-scan (depth) and B-scan, plus a follow-up view.

Discontinuities and features shown: near-surface delamination, shallow delamination, deep delamination, porosity, foreign material, impact damage, ply wrinkle and bondline disbond.

  • General Industry
  • Aerospace: Composite laminates and bonded structure: porosity, delamination and disbond maps for material review board disposition.
  • Wind Energy: Blade laminate and spar cap samples, and bonded test panels.

Open this demo

Ultrasonic Thickness Testing (UTT): Dual Element

Remaining wall thickness on piping, vessels, tanks and structures. Views in the demo: A-scan, thickness profile and thickness map, plus a follow-up view.

Discontinuities and features shown: general wall loss, isolated pit, pitting cluster, narrow pit and mid-wall lamination.

  • General Industry
  • Aerospace: Remaining skin thickness after corrosion removal and blend-out, against the structural repair manual limits.
  • Oil & Gas: Corrosion monitoring locations and internal pitting surveys.
  • Power & Nuclear: Wall loss surveys on service water and other plant piping.
  • Wind Energy: Remaining wall in towers, monopiles and transition pieces, including the splash zone offshore.
  • Civil & Infrastructure: Metal loss on steel bridge members and piles.
  • Marine & Shipbuilding: Hull gauging and tank wall readings.

Open this demo

Through Transmission Ultrasonics (TTU): Water Jet

Laminates and bonded assemblies where one reflection is not enough to read the part. Views in the demo: received signal, amplitude profile and C-scan, plus a follow-up view.

Discontinuities and features shown: porosity, shallow delamination, foreign material, impact damage, ply wrinkle, deep delamination and bondline disbond.

  • General Industry
  • Aerospace: Composite skins, honeycomb sandwich panels and bonded assemblies scanned with water-jet probes.

Open this demo

Total Focusing Method (TFM): Full Matrix Capture

Imaging where every point in the region is focused, from a single acquisition that can be reprocessed later. Views in the demo: direct (first leg (TT)), second leg (TT-TT), self-tandem (TT-T), C-scan and FMC data, plus a follow-up view.

Discontinuities and features shown: toe crack, cluster porosity, side-wall lack of fusion, slag line, incomplete penetration and root crack.

  • General Industry
  • Oil & Gas: Weld and corrosion imaging where a sharper image helps separate geometry from discontinuities.
  • Power & Nuclear: Thick-wall pressure-boundary girth welds in steel piping: the image modes separate root geometry from root cracks and image a steep side wall, and the full data set is kept for comparison at the next outage.
  • Marine & Shipbuilding: Thick hull and naval welds imaged with every point in focus, from data that can be reprocessed.

Open this demo

Dual Linear Array (DLA): Angle Beam

Austenitic stainless and other coarse-grained welds, where a shear wave scatters in the weld metal. Views in the demo: S-scan, A-scan, noise compared, C-scan and echo amplitude, plus a follow-up view.

Discontinuities and features shown: lack of fusion (far face), root crack and stress corrosion cracking.

  • General Industry
  • Oil & Gas: Stainless and clad process piping welds, corrosion-resistant alloy welds and cast stainless components, examined with longitudinal waves.
  • Power & Nuclear: Dissimilar metal welds at nozzles and safe ends, including stress corrosion cracking in the nickel-alloy weld and buttering at the inside surface, and austenitic piping welds, including intergranular stress corrosion cracking at the inside surface.

Open this demo

Ultrasonic Pulse Velocity (UPV): Concrete

Uniformity surveys of concrete walls, columns and foundations, finding honeycombing, voids and damaged surface layers by the drop in pulse velocity. Views in the demo: received waveform, pulse velocity, velocity contour map and indirect method, plus a setup view and a follow-up view.

Discontinuities and features shown: sound concrete, honeycombing, surface-opening crack, void and fire-damaged surface layer.

  • General Industry
  • Civil & Infrastructure: Bridge piers, abutments, columns and walls: uniformity surveys, honeycombing and voids, and fire- or freeze-thaw-damaged surface layers, with cores taken where the velocity is low.

Open this demo

Impact-Echo (IE): Concrete

Slab and wall thickness from one face, and delaminations, voids and honeycombing in concrete floors and foundations. Views in the demo: time waveform, amplitude spectrum and thickness map, plus a setup view and a follow-up view.

Discontinuities and features shown: sound slab, delamination, wide shallow delamination, void in a tendon duct, fully grouted duct and honeycombing.

Open this demo

Ultrasonic Tomography (UST): Concrete, Shear-Wave Array

Cross-section images of concrete from one face: rebar and duct layout, delaminations, voids and member thickness. Views in the demo: B-scan and C-scan depth slice, plus a setup view and a follow-up view.

Discontinuities and features shown: back wall, rebar mat, fully grouted duct, grouting void in a duct, delamination and honeycombing.

Open this demo

Electromagnetic Testing

High Frequency Eddy Current (HFEC)

Surface-breaking cracks in conductive materials. Views in the demo: impedance plane and strip chart, plus a setup view and a follow-up view.

Discontinuities and features shown: surface crack, corrosion pit, coating change and subsurface crack.

  • General Industry
  • Aerospace: Fatigue cracks at fastener holes, fillet radii and edges on aluminum and titanium structure.
  • Oil & Gas: Surface cracks at coated carbon steel weld toes and components, through thin coatings.
  • Power & Nuclear: Surface cracks on turbine and generator components.
  • Wind Energy: Small-area crack checks on bolting, shafts and coated welds.
  • Civil & Infrastructure: Crack checks through paint at bridge girder details and welds.

Open this demo

Bolt Hole Eddy Current (BHEC)

Cracks in the bore of open fastener holes. Views in the demo: impedance plane, time base and bore map, plus a setup view and a follow-up view.

Discontinuities and features shown: corner crack (top layer), bore crack (second layer), corrosion pit, tool mark and crack from rubbing between layers (not found by this technique; the follow-up view shows what is used instead).

  • General Industry
  • Aerospace: Fastener hole bores opened during repair or modification, probe matched to each reamed diameter.

Open this demo

Low Frequency Eddy Current (LFEC)

Subsurface cracks and corrosion in layered conductive structure. Views in the demo: impedance plane and strip chart, plus a setup view and a follow-up view.

Discontinuities and features shown: first-layer crack, second-layer crack, corrosion between the layers and crack under a fastener head.

Open this demo

Remote Field Testing (RFT)

Wall loss in ferromagnetic tubes from the inside. Views in the demo: voltage plane, mix plane and strip chart, plus a setup view and a follow-up view.

Discontinuities and features shown: wear at a tube support, outside pit, inside pit and general wall loss.

Open this demo

Eddy Current Testing (ET): Bobbin Probe, Tubing

Pitting, wear and wall loss in nonmagnetic heat exchanger and condenser tubes, examined from the inside. Views in the demo: impedance plane, mix plane, strip chart and phase-depth curve, plus a setup view and a follow-up view.

Discontinuities and features shown: wear at a tube support, outside pit, inside pit and circumferential crack at the expansion.

  • General Industry
  • Oil & Gas: Stainless steel, copper alloy and titanium tubes in heat exchangers, coolers and condensers.
  • Power & Nuclear: Nuclear steam generator tubing, and condenser and feedwater heater tubing in nonmagnetic alloys.
  • Marine & Shipbuilding: Copper-nickel and other nonmagnetic tubes in seawater coolers, condensers and heat exchangers.

Open this demo

Eddy Current Testing (ET): Rotating and Array Probes, Tubing

Cracks and pits at tube ends, expansions and supports that bobbin coils cannot characterize. Views in the demo: C-scan and impedance plane, plus a setup view and a follow-up view.

Discontinuities and features shown: circumferential crack, axial crack and outside pit.

  • General Industry
  • Oil & Gas: Expansion transitions and support areas in stainless steel exchanger tubes, and bobbin indications that need characterizing.
  • Power & Nuclear: Steam generator tubes at the top of the tubesheet, expansion transitions, U-bends and supports: axial and circumferential cracking, pits and wear.
  • Marine & Shipbuilding: Tube ends, expansions and bobbin indications in seawater coolers and condensers.

Open this demo

Near Field Testing (NFT)

Inside erosion, pitting and grooving in carbon steel tubes. Views in the demo: strip chart and inner-surface map, plus a setup view and a follow-up view.

Discontinuities and features shown: inlet-end erosion, inside pitting, inside groove and outside wall loss.

  • General Industry
  • Oil & Gas: Finned carbon steel air-cooler (fin-fan) tubes, where the fins rule out outside access: inlet-end erosion and inside pitting.

Open this demo

Eddy Current Testing (ET): Partial Saturation, Tubing

Ferritic and duplex stainless steel and nickel-copper tubes, too magnetic for bobbin coils alone. Views in the demo: impedance plane and strip chart, plus a setup view and a follow-up view.

Discontinuities and features shown: wear at a tube support, outside pit, inside pit and permeability variation.

Open this demo

Alternating Current Field Measurement (ACFM)

Surface-breaking cracks, with length and depth estimated from the Bz and Bx traces. Views in the demo: bx and Bz and butterfly plot, plus a setup view and a follow-up view.

Discontinuities and features shown: joined-up toe cracks, shallow toe crack, transverse crack and coating change.

Open this demo

Eddy Current Testing (ET): Conductivity

Screening heat treatment condition and sorting mixed conductive materials, with visual examination of the area. Views in the demo: readings, impedance plane and reading map, plus a setup view and a follow-up view.

Discontinuities and features shown: heat-damaged zone, thick paint (not compensated) and far-face heat damage.

Open this demo

Eddy Current Array (ECA)

Surface-breaking cracks and pitting mapped over an area in one encoded pass, with a C-scan record. Views in the demo: C-scan, strip chart and impedance plane, plus a setup view and a follow-up view.

Discontinuities and features shown: longitudinal crack, transverse crack, pitting colony, scratch (not a crack) and lamination (not found by this technique; the follow-up view shows what is used instead).

  • General Industry
  • Aerospace: Skin, fitting and wheel surfaces mapped for cracks and corrosion pitting, with an encoded record.
  • Oil & Gas: Weld cap and toe areas mapped for surface cracks through thin coatings.
  • Power & Nuclear: Surface cracks on turbine, generator and piping components, mapped with an encoded record.
  • Wind Energy: Tower flange and door frame weld toes scanned through the coating for fatigue cracks.
  • Civil & Infrastructure: Girder and connection weld toes scanned through paint for fatigue cracks, with an encoded record.
  • Marine & Shipbuilding: Weld toes and plate surfaces mapped for surface cracks through thin coatings.

Open this demo

Guided Wave Testing

Long Range Ultrasonic Testing (LRUT): Guided Wave

Screening long runs of pipe from a single location to find where to measure directly. Views in the demo: distance plot, plus a setup view and a follow-up view.

Discontinuities and features shown: corrosion at a support, corrosion patch, small isolated pit and flange (end of line).

Open this demo

Short Range Ultrasonic Testing (SRUT): Guided Wave

Areas next to the probe that cannot be reached directly. Views in the demo: distance plot, plus a setup view and a follow-up view.

Discontinuities and features shown: corrosion at the weld toe, soil-side corrosion and lap weld to the floor plates.

  • General Industry
  • Oil & Gas: Tank annular plates under the shell, and pipe at supports and clamps, screened with the asset in service.

Open this demo

Radiographic Testing

Radiographic Testing (RT): Film

Volumetric examination of welds and castings with a permanent image. Views in the demo: radiograph and line profile, plus a follow-up view.

Discontinuities and features shown: cluster porosity, lack of fusion, tight lack of fusion, slag, crack, transverse crack, incomplete penetration, root concavity, burn-through, tungsten inclusion, aligned porosity and lamination.

Open this demo

Radiographic Testing (RT): Computed Radiography

Radiography with a reusable plate and a digital image. Views in the demo: radiograph and line profile, plus a follow-up view.

Discontinuities and features shown: cluster porosity, lack of fusion, tight lack of fusion, slag, crack, transverse crack, incomplete penetration, root concavity, burn-through, tungsten inclusion, aligned porosity and lamination.

  • General Industry
  • Aerospace: Radiography of welded assemblies and castings with reusable imaging plates and a digital image.
  • Oil & Gas: Pipe and vessel weld radiography with reusable imaging plates and a digital image.
  • Power & Nuclear: Weld and component radiography with digital archiving.
  • Marine & Shipbuilding: Hull and piping weld radiography with reusable imaging plates and a digital record.

Open this demo

Radiographic Testing (RT): Digital Radiography

Radiography with an immediate digital image. Views in the demo: radiograph and line profile, plus a follow-up view.

Discontinuities and features shown: cluster porosity, lack of fusion, tight lack of fusion, slag, crack, transverse crack, incomplete penetration, root concavity, burn-through, tungsten inclusion, aligned porosity and lamination.

Open this demo

Computed Tomography (CT)

Three-dimensional location and sizing of internal features. Views in the demo: projection, sinogram and slice, plus a follow-up view.

Discontinuities and features shown: pores, shrinkage, crack, inclusion and rings (non-relevant).

Open this demo

Neutron Radiographic Testing

Neutron Radiographic Testing (NR)

Seals, adhesives, water and other hydrogen-rich materials inside metal housings and assemblies, which X-rays barely show. Views in the demo: neutron radiograph, X-ray compared and image quality, plus a follow-up view.

Discontinuities and features shown: missing O-ring section, water in the cavity, adhesive bond void and porosity in the cast wall.

  • General Industry
  • Aerospace: Residual ceramic core in turbine blade cooling passages, moisture and corrosion in honeycomb, and seals and adhesives inside metal assemblies.
  • Power & Nuclear: Irradiated fuel and sealed components by the transfer method: hydride in zirconium alloy cladding, pellet gaps and chips, and water or seal condition.

Open this demo

Magnetic Particle Testing

Magnetic Particle Testing (MT): Bench, Wet Fluorescent

Surface and near-surface cracks in ferromagnetic production parts, lot by lot. Views in the demo: head shot, coil shot and field check, plus a follow-up view.

Discontinuities and features shown: seam, fillet crack, lap, subsurface discontinuity and non-relevant indications.

  • General Industry
  • Aerospace: Shafts, pins, gears and landing gear parts inspected to the customer specification.
  • Oil & Gas: Bolting, valve stems and drilling components.
  • Power & Nuclear: Turbine and valve studs and bolting, examined on the bench at overhaul.
  • Marine & Shipbuilding: Propeller and tail shafts, rudder stocks and pintles, and bolting removed at overhaul.

Open this demo

Magnetic Particle Testing (MT): Yoke

Surface cracks at welds and in ferromagnetic structures in the field. Views in the demo: indication and fluorescent, plus a follow-up view.

Discontinuities and features shown: toe crack, transverse crack, subsurface discontinuity, crater crack and toe geometry.

Open this demo

Magnetic Particle Testing (MT): Prods

Heavy plate weldments and castings, where prods with half-wave current and dry powder reach a little further below the surface than an AC yoke. Views in the demo: indication, plus a follow-up view.

Discontinuities and features shown: toe crack, transverse crack, subsurface discontinuity, crater crack and toe geometry.

  • General Industry
  • Oil & Gas: Carbon steel vessel, piping and structural welds in shop fabrication; not on quenched-and-tempered steels or finished surfaces, where a yoke is used.
  • Power & Nuclear: Heavy carbon steel welds and castings in fabrication; arc-sensitive alloys and finished surfaces get a yoke instead.
  • Wind Energy: Tower shell and flange welds in fabrication, before coating, away from the machined flange face.
  • Civil & Infrastructure: Structural steel welds in building and plant fabrication; arc-sensitive high-strength steels get a yoke instead.
  • Marine & Shipbuilding: Routine shipyard practice on hull block, deck and bulkhead butt and fillet welds: dry powder on bare steel, with any arc strike ground out.

Open this demo

Liquid Penetrant Testing

Liquid Penetrant Testing (PT): Type I Fluorescent

Fluorescent penetrant, at the sensitivity level the procedure sets, for fine surface cracks on non-porous parts. Views in the demo: under UV-A, bleed-out curve and process, plus a follow-up view.

Discontinuities and features shown: shrinkage crack, porosity, cold shut, smeared crack and poor removal.

Open this demo

Liquid Penetrant Testing (PT): Type II Visible

Surface cracks in the field where a darkened area is not practical. Views in the demo: indication, bleed-out curve and process, plus a follow-up view.

Discontinuities and features shown: toe crack, crater crack, porosity, transverse crack, lack of fusion and undercut.

  • General Industry
  • Oil & Gas: Stainless and non-ferrous welds, with low-halogen materials on austenitic stainless.
  • Power & Nuclear: Field welds and repairs.
  • Wind Energy: Non-magnetic parts and spot checks where magnetic particle testing is impractical.
  • Civil & Infrastructure: Confirming fatigue cracks found by visual examination at bridge details and welds.
  • Marine & Shipbuilding: Stainless steel and other non-magnetic piping welds, with low-halogen materials on stainless.

Open this demo

Magnetic Flux Leakage

Magnetic Flux Leakage (MFL): Tank Floor and Plate

Screening of steel plate for metal loss on either face, with prove-up by thickness measurement. Views in the demo: sensor traces and tank floor map, plus a setup view and a follow-up view.

Discontinuities and features shown: underside pit pair (soil side), topside pit, broad corrosion on the underside and pit at the lap weld.

Open this demo

Infrared Thermographic Testing

Infrared Thermographic Testing (IRT): Pulsed Flash

Screening of thin laminates and coatings for near-surface discontinuities. Views in the demo: raw frame, contrast, contrast curve and cooling curve, plus a follow-up view.

Discontinuities and features shown: shallow delamination, deeper delamination, impact damage, porosity, flange disbond, foreign material, small deep delamination and kissing bond.

Open this demo

Infrared Thermographic Testing (IRT): Long Pulse

Deeper planes than flash heating reaches. Views in the demo: raw frame, phase image and contrast curve, plus a follow-up view.

Discontinuities and features shown: shallow delamination, mid-depth delamination, deep delamination, porosity layer, web disbond, wrinkle and deepest small delamination.

Open this demo

Infrared Thermographic Testing (IRT): Passive

Temperature patterns on equipment in service. Views in the demo: thermogram and line profile, plus a follow-up view.

Discontinuities and features shown: pipe support, flange, damaged insulation, wet insulation, open jacket seam, bare aluminum jacketing and corrosion under insulation.

Open this demo

Infrared Thermographic Testing (IRT): Fluid Ingress

Trapped moisture in sandwich structure. Views in the demo: thermogram and contrast curve, plus a follow-up view.

Discontinuities and features shown: water in cells, isolated wet cell, resin fill at an insert and repair patch.

Open this demo

Infrared Thermographic Testing (IRT): Bonded Doubler

Disbonds in bonded assemblies. Views in the demo: thermogram and contrast curve, plus a follow-up view.

Discontinuities and features shown: edge disbond, adhesive void, adhesive porosity and kissing bond.

Open this demo

Infrared Thermographic Testing (IRT): Step Heating

Subsurface features that change how a part warms. Views in the demo: thermogram, warming curve and contrast, plus a follow-up view.

Discontinuities and features shown: shallow delamination, impact damage, bonded insert and thickness step.

Open this demo

Shearographic Testing

Shearographic Testing: Vacuum Stressing

Bonded and composite structure under small applied loads. Views in the demo: shear horizontal, shear vertical, filtered, slope map and fringes against vacuum, plus a follow-up view.

Discontinuities and features shown: skin-to-core disbond, skin delamination, impact and crushed core, edge disbond, water in the core, core splice and far-side disbond.

Open this demo

Digital Image Correlation (DIC): Stereo

Full-field strain and displacement of parts under load. Views in the demo: strain map, out-of-plane and strain along a line, plus a follow-up view.

Discontinuities and features shown: hole edge concentration, damage from the notch, patch disbond and internal damage.

Open this demo

Leak Testing

Leak Testing (LT): Vacuum Box Bubble

Locating leaks in welds and seams. Views in the demo: through the window, bubble rate and seam map, plus a follow-up view.

Discontinuities and features shown: sound seam (no leak), pinhole leak, weld ripple (sound), gross leak, slow-forming leak and blocked leak path.

Open this demo

Leak Testing (LT): Pressure Change

Tightness of closed systems over a hold period. Views in the demo: recorder and hold detail, plus a follow-up view.

Discontinuities and features shown: tight system (no leak), small leak, gross leak, temperature drift and leaking valve seat.

Open this demo

Visual Testing

Visual Testing (VT): Direct

Usually the first examination of a part or weld, and a basis for planning further examination. Views in the demo: what the examiner sees and conditions, plus a follow-up view.

Discontinuities and features shown: toe crack, undercut, surface porosity, arc strike, spatter and grinding marks.

  • General Industry
  • Aerospace: Airframe and engine component inspection.
  • Oil & Gas: Welds and equipment in fabrication and turnarounds.
  • Power & Nuclear: Close visual examination of welds, bolting and component surfaces for cracks, corrosion, wear and erosion, and general visual examination of supports and internals for their condition.
  • Wind Energy: Tower, flange and blade surfaces examined directly, by rope access or from a platform.
  • Civil & Infrastructure: Bridge and building members.
  • Marine & Shipbuilding: Hull, deck and tank welds in new construction and repair, and structure in class and owner surveys.

Open this demo

Visual Testing (VT): Weld Inspection

Weld size, profile and surface condition before volumetric examination. Views in the demo: profile, plan view and fillet station, plus a follow-up view.

Discontinuities and features shown: hi-lo (misalignment), undercut, excess cap height, overlap, underfill, porosity and crater crack.

Open this demo

Visual Testing (VT): Remote

Internal surfaces reached through existing openings. Views in the demo: camera view and bore map, plus a follow-up view.

Discontinuities and features shown: root crack, incomplete penetration, root concavity, burn-through, pitting, erosion grooves and rust mounds (tubercles).

  • General Industry
  • Aerospace: Engine turbine and compressor stages through borescope ports, between overhauls; findings are recorded for disposition under the engine manual by the cognizant engineering organization.
  • Oil & Gas: Vessel, exchanger and piping internals without entry.
  • Power & Nuclear: Boiler tubes, headers and turbine internals.
  • Marine & Shipbuilding: Seawater and ballast piping bores and their girth weld roots, where they cannot be seen directly.

Open this demo

Visual Testing (VT): Field Metallographic Replication

Microstructure of in-service components without cutting a sample. Views in the demo: replica and damage by zone, plus a follow-up view.

Discontinuities and features shown: isolated cavities, aligned cavities, linked microcracks and spheroidized carbides.

  • General Industry
  • Oil & Gas: Fired heater and high-temperature equipment microstructure after a fire or overheat.
  • Power & Nuclear: Creep damage in high-temperature headers and steam lines, at the same locations each outage.

Open this demo

Visual Testing (VT): Field Metallographic Microscopy

First read of microstructure on site. Views in the demo: microstructure and picral etch, plus a follow-up view.

Discontinuities and features shown: decarburized layer, ferrite and pearlite, partial spheroidization, full spheroidization and graphitization.

Open this demo

Visual Testing (VT): Optical Prism and Mirror Aids

Welds and surfaces just out of direct view. Views in the demo: mirror view and conditions, plus a follow-up view.

Discontinuities and features shown: toe crack, undercut and undersized fillet.

  • General Industry
  • Aerospace: Acrylic cabin windows: cracks at the edge and the mounting holes, crazing, scratches and chipping, seen through a window inspection prism. Limits come from the aircraft maintenance manual.
  • Oil & Gas: Inside corners, nozzles and welds with restricted access.
  • Power & Nuclear: Welds with restricted access.
  • Civil & Infrastructure: Bearings, backs of connections and hidden fatigue details reached with mirrors and optical aids.
  • Marine & Shipbuilding: Welds behind brackets, stiffeners and pipework in tanks and machinery spaces.

Open this demo

Acoustic Emission Testing

Acoustic Emission Testing (AE)

Global monitoring of pressure vessels and structures while they are loaded. Views in the demo: hit waveform, location plot, amplitude and hits and load, plus a setup view and a follow-up view.

Discontinuities and features shown: active crack, leak at a fitting, friction at a saddle and dormant corrosion.

Open this demo

Ground Penetrating Radar

Ground Penetrating Radar (GPR): Concrete Scanning

Locating tendons, rebar and conduit in concrete, with slab thickness and void screening. Views in the demo: radargram, trace and depth slice, plus a setup view and a follow-up view.

Discontinuities and features shown: near-surface delamination, unbonded tendon, air-filled conduit, void under the slab and honeycombing under a tendon.

Open this demo

Bond Testing

Bond Testing: Mechanical Impedance Analysis (MIA)

Skin-to-core disbonds and crushed core in honeycomb panels and bonded repairs, mapped for the repair engineer. Views in the demo: amplitude/phase, C-scan and coverage, plus a setup view and a follow-up view.

Discontinuities and features shown: near-side disbond, crushed core, skin delamination, far-side disbond and doubler disbond.

  • Aerospace
  • Wind Energy: Skin-to-core separations and core damage in blade shell sandwich areas and repairs.
  • Marine & Shipbuilding: Skin-to-core disbonds and crushed core in composite hull, deck and superstructure sandwich and repairs.

Open this demo

Bond Testing: Pitch-Catch

Near-side disbonds in honeycomb panels with dry tips and no couplant, mapped over the area. Views in the demo: RF signal, amplitude/phase, C-scan and coverage, plus a setup view and a follow-up view.

Discontinuities and features shown: near-side disbond, crushed core, skin delamination, far-side disbond and doubler disbond.

  • Aerospace
  • Wind Energy: Skin-to-core disbonds in blade shell sandwich areas, mapped over the area.
  • Marine & Shipbuilding: Near-side and far-side skin-to-core disbonds in composite hull and deck sandwich, mapped over the area.

Open this demo

Bond Testing: Resonance

Delaminations and bondline separations in laminates, thin skins and bonded doublers. Views in the demo: impedance plane, frequency sweep, C-scan and coverage, plus a setup view and a follow-up view.

Discontinuities and features shown: near-side disbond, crushed core, skin delamination, far-side disbond and doubler disbond.

  • Aerospace
  • Wind Energy: Laminate delaminations and bonded doubler separations in blade shells.
  • Marine & Shipbuilding: Laminate delaminations and bonded doubler separations in composite hull and deck structure.

Open this demo

Explore Our Techniques, Industry by Industry

General Industry

Aerospace

Oil & Gas

Power & Nuclear

Wind Energy

Civil & Infrastructure

Marine & Shipbuilding